Brick Paver Installation & Edging



Staging of product

A lot of paver projects will differ depending on gain access to, site conditions, task size and obviously, the weather condition. These circumstances can have a total impact on your task from a timing stand point. Careful factor to consider should be required to determine the time to begin the paver installation. Always attempt to avoid any traffic or lessen on the prepared locations.

The foreman or task manager must always have the products (sand/ pavers) dispersed around the job website for effective and easy setups. Paver pallets/bundles need to be put in a way not to interfere with the paver installation. The correct pallet/bundle placement can make the actual job installation much easier and quicker by decreasing the total labor of handling the product.

Brick paver patterns

Pavers can be placed in various patterns depending upon their shape. Each paver shape will typically have numerous different hatch patterns that are offered by the maker.

Contractors need to take into factor to consider the traffic weight loads on their paver tasks. In many applications around the world, it has been shown that pavers laid in a herringbone pattern have actually carried out effectively.

Pavers that are 60 mm (2 - 3/8 in) thickness are suitable for pedestrian applications. Pavers that are going to be utilized in business or industrial applications should be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that figure out the starting point of a paver project.

When beginning to set up pavers it is best to snap a real straight chalk line on the surface of the bedding sand or pull a true straight string line above the surface area of the bed linen sand at the ended up elevation of the pavers This will help as a guide for preserving straight joint lines and will likewise permit the installer to make adjustments in the alignment of the pavers.

Buildings and concrete suppressing are usually not straight and should not be used for developing straight joint lines. The use of string lines is necessary to figure out the true straightness of the edge too. As the paver installation advances, the string lines will assist minimize the need for small trim pieces.

These will preserve a minimum joint width and enable the bed linen and jointing sand to get in in between each paver. Pavers with spacer bars are generally not laid in snug against each other since a string line will provide consistent joint spacing.

Installation of brick pavers.

One of the most commonly used methods for the installation of pavers is hand installation of each paver. It is best to set up a single row of pavers along one of the real straight lines that you have pulled or above the bedding sand. The best method is to place a paver against another one and let it slide down into the bedding sand.

When setting up pavers on a high grade, they need to be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

The finest way for installing pavers on big jobs is to install them mechanically. There are a couple items a contractor should think about prior to setting up pavers mechanically:

1.) Mechanical installers are only capable of installing pavers in certain patterns.

2.) The specialist needs to ensure that the producer is capable of manufacturing and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

3.) Professionals may encounter a color blending scenario coming off the packages of pavers Poor color mixing could result in an irregular looking installation. A lot of producers are consistent with color blending on each package of pavers, however it is the professional's responsibility to ensure correct blending in the field.

Cutting procedures for brick pavers.

Professionals generally have 2 methods of cutting pavers. When cutting pavers wet, it will assist reduce dust and will prolong the diamond blades life. The operator of the brick saw need to always cut the pavers away from the surface of the paver field when cutting damp, due to the fact that the pavers will develop a slurry that will stain the paver surface area.

The brick saw operator should constantly wear the correct security that is needed for running a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a major role in the general success of an interlocking pavement installation Edging restraints eliminate lateral motion of the pavers and hold the pavers firmly together. Specifically at the external perimeter of the paver application, without an edging restraint, your task is ensured to fail with time.

There are a number of various edging restraints from which professionals can choose. Usually manufactured edge restraints are the most frequently used by specialists. Produced edging Paver Installation Boca Raton restraints can vary from, plastic edging, steel and aluminum, woods or precast concrete and stone. An edging type that is utilized mainly in commercial and industrial applications is poured-in-place concrete curbs. This edging restraint is typically set up by other contractors.

Edging installation.

This might result in the migration of the bedding sand and eventual lateral motion of the pavers. If there is a possibility of losing bedding sand between the pavers and the edge restraint, then geo textile material is advised. When a gap in between the pavers and the edging goes beyond 3/8" (10mm), then the space must be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The entire area that is to be compressed need to be swept clean of any foreign items and particles that can trigger scuffing or scratching on the surface of the pavers.

It is essential to have a compactor that can apply between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is necessary that the first compaction happens before any jointing sand has been applied to the pavers. If jointing sand is applied to the pavers prior to compaction takes place, this can cause a bridging issue and will not permit the joints to be completely filled with jointing sand. This can likewise avoid the pavers from being properly set into the bedding sand.

When compacting the pavers, it is suggested that you make a minimum of 2 passes in different directions across the pavers. This will enable the pavers to be appropriately embeded in the bedding sand and will force the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is extremely vital to the last efficiency of the pavers. Failure to do proper compaction can result in deformations and pavement failure gradually.


Paver pallets/bundles need to be placed in a manner not to interfere with the paver installation. One of the most commonly used approaches for the installation of pavers is hand installation of each paver. The operator of the brick saw need to constantly cut the pavers away from the surface of the paver field when cutting wet, due to the fact that the pavers will produce a slurry that will stain the paver surface area. Edging restraints remove lateral motion of the pavers and hold the pavers securely together. When a space between the pavers and the edging exceeds 3/8" (10mm), then the area needs to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *